This site-wide search returns results for all documents and events in Tethys Engineering, prioritizing the best matches. Partial word matches are returned (e.g. "engineer" finds "engineering"), but every entered term must be found. If you don't find any results, try reducing the number of words entered or removing special characters. Filters to the right can help narrow your search. Tethys Engineering features an integrated search with other marine renewable energy databases in PRIMRE - click the buttons below "Showing Results for" to search other integrated databases.
Showing Results for
- Conference Paper:
Saouli et al.
… for high energetic sites and to deploy seven vertical axis tidal turbines on the Raz Blanchard site, France. This technology has already been successfully developed in a previous project at a smaller scale on the Paimpol-Bréhat test site. Along the past three years, an important amount of work has been achieved to widely …
- Conference Paper:
Cashman et al.
… conditions and are compared to results from the prototype device located at an experimental test site in Ireland. … 10069 …
- Conference Paper:
Moreau et al.
… tested its 1 MW-rated ducted twin vertical axis tidal turbine (2-VATT) at Paimpol-Bréhat test site, France. At this site, the turbulent intensity is evaluated about 15 % and extreme wave conditions up to 6 m …
- Journal Article:
Moreau et al.
… bottom mounted twin vertical axis tidal turbine (VATT) OceanQuest at the Paimpol-Bréhat site, off the coast of Brittany, France. Thus, two years of operational data are available to …
- Journal Article:
Birjandi et al.
… mean and fluctuating components of river flow velocity. Results show that in this particular test site the river contains eddies with the same order of magnitude as the turbine diameter or …
- Conference Paper:
Hill et al.
… device with a rotor diameter dT = 0.5 m. It was designed for a tidal current energy reference site modeled after the Tacoma Narrows in Puget Sound, WA [3]. RM2 is a 1:15 scale dual-rotor … diameter dT = 0.43 m and rotor height hT = 0.32 m. It was designed for a river current energy site modeled after a reach in the lower Mississippi River near Baton Rouge, LA [4]. Results …
- Journal Article:
Laws and Epps
… five areas that are positioned to significantly impact the viability of HEC technology: (i) site assessment, (ii) turbine design, (iii) turbine wake modeling, (iv) array performance, and ( …
- Journal Article:
Niebuhr et al.
… not been considered. Some attempts have been made to develop backwater models, but these were site-specific and performed under constant operational conditions. Therefore, the aim of this …
- Conference Paper:
Zhao et al.
… The blade embedded actuation allows for reasonable flow conditions. For full scaled on-site applications this is required to reduce hydrodynamic losses and to protect the actuators and … as compared with the original one, while almost the same power is required. An experimental test bench for a single blade with both types of actuators is built to verify their ability of a …
- Report:
Igiugig Village Council
… minimal infrastructure or personnel requirements. If future funding is available to build and test the system, UW-APL will be able to perform all or part of the fabrication, assembly, and … it was recommended to allow approximately four months for system delivery. In addition to the site-specific application at Igiugig, the UW-APL design is applicable to a wide range of uses as …
- Report:
Hill et al.
… rotor diameter dT = 0.43m and rotor height, hT = 0.323m. RM2 is a river turbine designed for a site modeled after a reach in the lower Mississippi River near Baton Rouge, Louisiana (Barone et …
- Thesis:
Cavagnaro
… with a mean of 2 m/s is generated from high-resolution flow measurements of a riverine site and is used to drive emulation. Power output during emulation under similar input and …
Displaying 1 - 12 of 12